| ROBO
Anti-Spatter TMS-PI Internal Injector |
|
|
|
|
|
 |
|
|
|
The
ABICOR Binzel® TMS-PI Anti-Spatter Injector is essential to front
end welding torch maintenance, providing an adjustable, measured amount
of anti-spatter fluid with the torch airblast. All ABICOR Binzel robotic
torches are equipped with airblast capability. For maximum spatter
removal, the Airblast Anti-Spatter can be used in conjunction with
the ABICOR Binzel TCS-6 Cleaning Station. |
|
|
|
|
|
|
|
|
|
|
|
| Working
Pressure: |
6-8
bar/85-120 psi |
| Inlet
Connection: |
1/4"
hose barb |
| Reservoir
Capacity: |
32
oz |
| Requirements: |
1
output |
|
24
VDC or 110 VAC |
| 24
VDC: |
0.3
Amps, Max @ 6 watts, 250 mA operating |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Model
|
Part
No.
|
| TMS-PI
Internal Injector Anti-Spatter Unit 24VDC, 16 oz |
832.9100-HF
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ITEM
NO.
|
DESCRIPTION
|
SPECIFICATIONS
|
PART
NO.
|
|
-
|
TMS-PI
Hi-Flow Anti-Spatter Internal Injector 24VDC/110VAC |
-
|
832.9100-HF
|
|
1
|
Reservoir |
32
oz
|
832.9104
|
|
2
|
Mounting
Block Top |
-
|
832.9134
|
|
3
|
Injector
Body Bottom |
-
|
832.9135
|
|
4
|
Solenoid
Valve 24VDC/110VAC with 15' cord |
-
|
832.9135
|
|
5
|
Pulse
Generator |
-
|
832.9112
|
|
6
|
Bracket
Mounting |
-
|
832.9113
|
|
7
|
Screw
Bracket, M6 x 75 (included with Item 6) |
2
Required
|
832.9138
|
|
8
|
Hose
Outer 1/4 ID |
per
meter
|
176.0008
|
|
9
|
Hose
Inner |
per
meter
|
832.9129
|
|
10
|
Fitting
Quick Coupler |
1
piece
|
832.9137
|
|
11
|
Fitting
Quick Coupler |
1
piece
|
832.9133
|
|
14
|
Reservoir
Cap (included with Item 1) |
-
|
832.9120
|
|
N/S
|
Injector
Body Rebuild Kit |
-
|
832.9118
|
|
N/S
|
Extension
Hose Kit 35' |
-
|
832.9100-EXT
|
|
N/S
|
Anti-Spatter
Fluid - Organic Oil Based - MSDS |
1
Gallon
|
192.9017
|
|
N/S
|
Anti-Spatter
Fluid - Organic Oil Based - MSDS |
5
Gallon
|
192.9012
|
|
N/S
|
Anti-Spatter
Fluid - Organic Oil Based - MSDS |
55
Gallon
|
192.9007
|
|
-
|
- |
-
|
-
|
|
-
|
N/S
= Not Shown |
-
|
-
|
|
|
|
|
|
|
|
|
TMS-PI
ANTI-SPATTER SET-UP
|
|
1. |
Attach
aluminum mounting bracket to a suitable location |
|
2. |
Attach
Anti-Spatter unit with 2 mounting screws supplied |
|
3. |
Connect
non-lubricated main air to air supply inlet 1/4" barb.
Air pressure to be min. 60 PSI and max. 120 PSI |
|
4. |
connect
solenoid valve wires to 24VDC or 110VAC robot output or PLC
output |
|
5. |
Fill
reservoir with suitable Anti-Spatter fluid. If unit has run
dry - or to prime - open drain plug to allow liquid to run freely
and bleed air from the unit. Unit is primed from the factory
and normally will prime after filling the reservoir. |
|
6. |
Connect
outer hose to welding torch connection. Inner hose may lie freely
and extend into the torch side hose. |
|
|
|
FLUID
/ PULSE ADJUSTMENTS
|
| 1. |
Injector
Stroke |
| - |
Rotate brass fluid adjustments knob to increase/decrease fluid
quantity. Clockwise to increase - counterclockwise to decrease |
| 2. |
Pulse
Frequency |
| - |
adjust
pulse frequency using standard screwdriver. Frequency range
is from 4-200 pulses per minute |
|
|
|
|
|
|
|
|
|
|
|
